Call Us
03 379 9662

FREE Measure & Quote anywhere in Christchurch! 

btn book now

User Manuals

Programming a 433 Remote      

To programme a 433 Remote, please follow these instructions, or alternatively download the following PDF file.

- Turn the power off to the unit for 5 seconds

- Turn the power back on

- Push "Programme" button twice (eg. push push)

- All 4 small red lights (LEDs) will light up & flash

- When the lights stop flashing, LED one will be on constant (not flashing), this means that it already has a remote control programmed in to it

- You must then push the "programme" button again once, the #2 LED will come on, if this is also constant (not flashing), it already has a remote control programmed in to it. (NOTE: each light represents a remote code)

- Keep pushing the "programme" button until one of the LEDs is flashing (this represents an empty memory slot).

- Once the light is flashing, push and hold the remote button until the light stops flashing, and release the remote button.

- Wait several seconds and automatically all lights will flash on and off. Once this has happened, you can use your remote.

 
To wipe a code on a 433 Remote, please follow these instructions, or alternatively download the following PDF file.

- Turn the power off to the unit for 20 seconds

- Push the "programme" button twice (eg. push push)

- After several seconds all lights will flash on & off. Light 1 will come on.

- If you want to delete the code on LIGHT 1, push and hold the "programme" button until the light starts to flash - the code is now wiped.

- You may then by pushing the "programme" button once, cycle through each LED light and delete when required.

 
dbimage file ZGJfaW1hZ2VzL3NlY3Rpb24vc2VjdGlvbl8yOS5qcGc= type resize width 200
Programming a Cobra Remote      

 To programme a Dominator Cobra remote, please follow these instructions, or alternatively download the following PDF file.

- Select "Handheld" mode using the "LEARN" button on the unit (display shows "H"

- Within 10 seconds, momentarily press the required button on the transmitter. The decimal point indicator on the display will flash and then stay on.

- Repress the same button again momentarily, the decimal point indicator will flash and then the display will show the memory location number for that function (eg. "H xx"). The location number "xx" will be the first free handheld location number in the memory.

- Your remote will now operate your door.



To delete a Dominator Cobra remote from memory, please follow these instructions, or alternatively download the following PDF file.

- Select "Erase" mode using the "LEARN" button on the unit (display shows "E")

- Press and hold a button on the required transmitter for 2 seconds until the decimal point stays on.

- Release the transmitter button until the decimal point turns off, then press the transmitter button again for 2 seconds; the decimal point will flash and then stay on.

- The display will flash twice (CLR) once the transmitter code has been removed from memory.

- If you do not have the remote that you want to delete from memory, after selecting "Erase" mode:

- Find the memory location of the transmitter to be erased - momentarily press button 1 on a transmitter to display the next used memory location number (eg. "H xx"). Momentarily pressing button 2 will display the previous memory location number (eg. "H xx").

- Once the memory location is located, momentarily pressing button 3 will clear the transmitter function that is memorised in the displayed location number. If no transmitters are stored in memory (memory empty) "H" will be displayed.
PTX4

Programming a GDO Remote      

To programme a Dominator GDO remote (for any of the GDO Tilt/Sectional models), please follow these instructions or alternatively download the following PDF file.

- Press and hold the "DOOR CODE" button

- Press one of the four buttons on the transmitter for 2 seconds, pause for 2 seconds, then press the same button again for 2 seconds.

- Release the "DOOR CODE" button

- Your remote will now work.



To delete a Dominator GDO remote, please follow these instructions or alternatively download the following PDF file.

- Select the transmitter you want to delete

- Press and hold the "DOOR CODE" button

- Press the transmitter button you would like to delete for 2 seconds, pause for 2 seconds, then press again for 2 seconds.

- Release the "DOOR CODE" button

- Test that this has deleted this transmitter from memory by attempting to operate the door.


If you do not have the remote present that you would like to delete, follow these instructions to delete all remotes in memory. You will then need to reprogramme your existing remotes.

- Turn off power to the opener

- While switched off, press and hold the "DOOR CODE" button. Turn power on to the unit while holding this button.

- The "Open Limit", "Close Limit" and "Door Status" LEDs will illuminate for about 5 seconds. These LEDs will turn off and CODING LED will illuminate.

- Release the "DOOR CODE" button. All stored codes will now be deleted. Confirm this by pressing buttons on any previously coded transmitters.
GDO9 Remote Cropped-316

User Manuals

Click on the image to download
GDO11 Manual Cover-971
 
GDO9 Manual Cover-467
 
GDO7 Manual Cover-801
 
GDO6 Manual Cover-1
GDO10 Manual Cover-29
 
Cobra Manual Cover-755
 
433 Manual Cover-488
 
   

CONTACT US

 
(03) 379 9662
Fax: (03) 365 8658
6 Newtown Street
Bromley
Christchurch
New Zealand
 
 

Secure Payment


logo secured payment

Member

logo cecc
 
  • logo footer1
  • logo footer2
  • logo footer3
  • logo footer4
  • logo footer5